What tool removes crankshaft pulley?

A half-inch drive impact gun might be a great tool for removing a stubborn crankshaft pulley bolt. A torque wrench has also been proven to be a helpful tool for correctly securing it.

How do I know if my crankshaft pulley is bad?

Bad Crankshaft Pulley/Harmonic Balancer Symptoms

1. 1) Engine Vibrations. The first symptom that will likely come up are engine vibrations.
2. 2) Alternator Failure. The crankshaft pulley is responsible for powering the alternator.
3. 3) Power Steering Pump Failure.
4. 4) Transmission Damage.
5. 5) Irregular Idle Engine Speed.

What causes crankshaft pulley failure?

Another way a pulley can fail is during the fitting process there has been an interruption with the assembly press or the friction bearing has been incorrectly pressed in. This can occur during the making and installation of the part with the vehicle.

How do you remove a pulley without a puller?

You can use a tool such as a pickle fork to remove the pulley and then rotate it a bit with a screwdriver. Do it again and again until the pulley is finally out.

Can you remove crank pulley with impact?

If your impact gun is strong enough then it’ll spin it off easily. Re: Impact Wrench to Remove Crank Pulley Bolt? No holder is needed when using an impact.

Can I drive with a bad crankshaft pulley?

Indeed, if it’s the crank pulley and the harmonic balancer comes off with it and the engine continues to run that can damage the crankshaft. Other pulleys could get distorted if a fastener is missing and in such condition could damage the drive belt riding on the pulley. …

How much does it cost to fix a crankshaft pulley?

The cost to replace a bad crankshaft pulley/harmonic balancer is anywhere from $350 to $400. The cost of labor is around $150 to $180 and the cost of parts is around $200 to $220.

What happens when a crankshaft pulley goes bad?

When a crankshaft pulley fails (or the timing belt due to a badly maintained crankshaft pulley), the timing of the engine is completely thrown off. Even a rotation or movement of a few millimetres can start to cause problems in a system so precise.

What to do if your crankshaft pulley is bad?

When you have the tools above, you can start removing the device. 1): Gently pull out the serpentine belt to gain access to the harmonic balancer. 2): Second, remove the bolt at the center with a wrench or pliers. The center bolt supports the dampener. It’s usually very tight. 3): Remove the equipped pulley.

Can a crankshaft be removed without pulling the engine?

Although crankshafts are traditionally removed after the engine has been pulled from the engine bay, it is possible to remove the crankshaft without pulling the engine. Step 1 Remove the engine’s belts.

What are symptoms of crankshaft pulley / harmonic balancer failure?

One of the crankshaft Pulley/harmonic Balancer failure symptoms is a very loud noise from the engine. When there is engine vibration, there will surely be a lot of loud noises coming from your engine. The noise will start to pop once you shift to a higher gear. If the noise becomes louder or is very loud, do not attempt to drive your car.

What kind of socket do you use for a crank pulley?

Using a 19 mm impact socket the crank pulley bolt came out like butter. Don’t use the Starter Bump Method to try and loosen the bolt. You run the risk of breaking your tools, Breaking something on the car, or stripping the bolt head. Use an Impact Socket 1/2 inch drive. You’ll probably break a standard socket. Use the 19mm for the Toyota Camry.

How to remove a crankshaft pulley in your car?

How to remove a crankshaft pulley on your engine, so you can change a timing belt or leaky oil seals. All you need is a simple pulley removing tool. DIY car repair with Scotty Kilmer, an auto mechanic for the last 43 years. 1. Bluetooth Scan Tool: http://amzn.to/2nfvmaD 2. Cheap Scan Tool: https://amzn.to/2D8Tvae 3.

How do you remove the pulley from a harmonic balancer?

Once each belt has been loosened, pull the belt away from the pulley which attaches to the harmonic balancer. Remove the pulley which attaches to the harmonic balancer. The pulley is secured to the balancer with three bolts. Remove each bolt with a wrench and pull the pulley away from the balancer. Remove the harmonic balancer.

How is a crankshaft removed from an engine?

Take care when removing the final cap, as the crankshaft is very heavy. To avoid injury, hold the crankshaft against the engine when the final cap is removed, then slowly lower the crankshaft out of the engine to complete the removal process.

How do you remove balancer from crankshaft?

Remove the harmonic balancer. Use a wrench to remove the single bolt from the center of the harmonic balancer. This bolt is used to connect the balancer to the snout of the crankshaft. Attach a harmonic balancer remover, to the face of the balancer with the supplied bolts.