How is a crankshaft pulley removal?

How to Remove a Crankshaft Pulley

1. Position the puller in front of the pulley.
2. Install the puller-to-pulley bolts.
3. Using a breaker bar and socket, tighten the central puller bolt until the pulley slides off the crankshaft.

How do you remove a crank pulley from a car?

Disassemble the crankshaft pulley You just have to place one end on the bolt-removing tool and slacken the bolt using an impact wrench. With the bolts included in your tool, you may now tighten the bolt remover tool. Keep doing this step until the crankshaft pulley is finally released.

Is Honda crank bolt reverse thread?

Good luck, usually those bolts are an absolute PITA to get out. Yes it’s lefty loosey, but a lot of them are really on tight.

When should I replace crankshaft pulley?

Signs that your crankshaft harmonic balancer needs to be replaced include:

1. The engine is loud and you feel vibrations coming from your engine.
2. The pulley belt may slip causing your vehicle to backfire or misfire.
3. The vehicle’s ignition timing will be off.
4. The vehicle will not start at all.

Which way does a crankshaft bolt loosen?

Place your socket on the crankshaft pulley bolt and wedge the end of your ratchet or breaker bar onto the ground. Make sure when the pulley starts to turn, the breaker bar is positioned to push the bolt counterclockwise to loosen it.

Is harmonic balancer reverse threaded?

“Right hand thread” means you turn CLOCKWISE to tighten, COUNTER-CLOCKWISE to loosen. Like most bolts/nuts. The fan is NOT reverse threaded.

Can a crankshaft pulley be removed from a Honda Civic?

The crankshaft pulley bolt is one of the most stubborn bolts on this era of Honda. Unfortunately, they also need to come off in order to remove the crankshaft pulley and the crankshaft seal behind it. Typically this is done in order to change the timing belt, but the crankshaft pulley itself will fail on its own as well.

How do you jack up a Honda Civic?

Use a two-post lift if that’s an option. If it’s not and you’re doing this in the driveway, just set the car up on jack stands. Remove the passenger’s side wheel. The crankshaft pulley is the single, large pulley at the bottom of the engine. Figure 1. Diagram of the jacking points. (Related Article: How to Jack Up Your Civic – Honda-Tech.com)

How do you unbolt a crank pulley bolt?

Attach a 17mm socket and attempt to unbolt the crank pulley bolt. In order for this to work, you’ll need an impact gun with more than 600 lb/ft of breakaway torque. If you have one handy, try it out. If it doesn’t work, then use a crank bolt removal tool. If the impact gun didn’t work, the next step is to use the crank bolt removal tool.

Can a crankshaft seal be replaced on a Honda Civic?

Also, the front crankshaft seal can be prone to leaking if it’s old or if it has been reused at any point. As much as a hassle this might be, the truth is it can be done at home as long as the right tools are used.

The crankshaft pulley bolt is one of the most stubborn bolts on this era of Honda. Unfortunately, they also need to come off in order to remove the crankshaft pulley and the crankshaft seal behind it. Typically this is done in order to change the timing belt, but the crankshaft pulley itself will fail on its own as well.

Use a two-post lift if that’s an option. If it’s not and you’re doing this in the driveway, just set the car up on jack stands. Remove the passenger’s side wheel. The crankshaft pulley is the single, large pulley at the bottom of the engine. Figure 1. Diagram of the jacking points. (Related Article: How to Jack Up Your Civic – Honda-Tech.com)

Attach a 17mm socket and attempt to unbolt the crank pulley bolt. In order for this to work, you’ll need an impact gun with more than 600 lb/ft of breakaway torque. If you have one handy, try it out. If it doesn’t work, then use a crank bolt removal tool. If the impact gun didn’t work, the next step is to use the crank bolt removal tool.

Also, the front crankshaft seal can be prone to leaking if it’s old or if it has been reused at any point. As much as a hassle this might be, the truth is it can be done at home as long as the right tools are used.