How do I know if my driver side wheel bearings are bad?

Here are some indicators of a worn wheel hub bearing or other wheel-end damage:

1. Snapping, clicking or popping.
2. Grinding when the vehicle is in motion.
3. Knocking or clunking.
4. Humming, rumbling or growling.
5. Wheel vibration and/or wobble.
6. Shudder, shimmy or vibration at a constant speed.

How do you change outer wheel bearings?

Part 1 of 3: Prepare your car

1. Materials Needed.
2. Step 1: Put chocks behind your wheels.
3. Step 2: Loosen the lug nuts.
4. Step 3: Lift up the vehicle.
5. Step 4: Remove the lug nuts.
6. Step 1: Remove the brake caliper and bracket.
7. Step 2: Remove the outer wheel bearing.
8. Step 3: Remove the rotor and inner wheel bearing.

Is it easy to change wheel bearings?

Is it easy to replace a wheel bearing at home? Replacing a wheel bearing that comes as an assembly with the hub and bolts to the spindle or steering knuckle is not very difficult if you have proper skills, tools and the manual. Of course, the large axle nut is very tight and can be difficult to remove.

How much does it cost to replace side wheel bearings?

The average cost for wheel bearing replacement is between $297 and $381. Labor costs are estimated between $158 and $199 while parts are priced between $139 and $181. This range does not include taxes and fees, and does not factor in your specific vehicle or unique location. Related repairs may also be needed.

How long will bad wheel bearing last?

However, a wheel bearing can last an average of anywhere from 136,000 to 160,000 km which is about 85,000 to 100,000 miles.

How long does it take to change a wheel bearing?

Rear wheel drive, tapered roller bearing: about 15-45 minutes; wear gloves or spend another 10 minutes washing grease off your hands. Front wheel drive with pressed on bearing: 30–120 minutes depending on whether it can be pulled off and pressed in with a specialty tool.

Can I drive on a noisy wheel bearing?

If a wheel bearing starts to get worn, it will start to make a noise. It is not a good idea to drive with a worn wheel bearing because it is an essential part of holding the wheel onto your vehicle. A rumbling or humming sound is another sign of a worn wheel bearing.

How do you change a front wheel bearing?

Step 1: Put chocks behind your wheels. Park the vehicle on a flat and level surface. Use a wheel chock to block the tire opposite of the wheel that you will be working on first. Tip:If you are changing the driver’s side front wheel bearing, you will will need to use a chock at the passenger rear wheel.

What’s the best way to replace a front wheel?

Use a glob of grease to coat the inner bearing race, then set the inner bearing down inside it. Take the inner wheel-bearing seal and install it as you did the bearing races, tapping it into place and taking care not to cock it, but only get it flush with the inner surface of the hub. Don’t pound it in any farther than that.

Where are the wheel bearings on a car?

This is because the front rotors are often behind the front hubs, which means that to change the rotors you have to pull the hubs off the front spindles, at which point the bearings are practically in your hand. So, if you need to do a front brake job, check the wheel bearings.

Where to put wheel chocks when changing wheel bearings?

For example, you would place wheel chocks behind the rear tires if you are fixing a front wheel bearing and behind the front tires if you are working on a rear wheel. Loosen the lug nuts and lift the wheel using a jack. For proper access to the internal components of the wheel whose bearings you’re replacing, you’ll need to elevate the wheel.

How do you change wheel bearings on a car?

To change wheel bearings, start by lifting the wheel up on a jack, unscrewing the lug nuts, and taking the wheel off. Then, remove the brake caliper, the dust cover over the rotor, and the cotter pin and castle nut behind the dust cover. Next, pull the rotor off, remove the old hub, and take apart the hub assembly to access the wheel bearings.

How to replace Ford Explorer rear wheel bearing-DIY?

This video outlines replacement of the rear wheel bearing, hub, parking brake shoes, brake rotors and pads. A shop press is required to service this bearing. The example vehicle is a 2002 Ford Explorer 4X4 however this example is similar to many 2000-2010 Ford Explorer and Mercury Mountaineer vehicles. Watch this video for more information.

Use a glob of grease to coat the inner bearing race, then set the inner bearing down inside it. Take the inner wheel-bearing seal and install it as you did the bearing races, tapping it into place and taking care not to cock it, but only get it flush with the inner surface of the hub. Don’t pound it in any farther than that.

When to replace a Colorado front wheel bearing?

This guide will show you how to replace a 2003-2012 Chevy Colorado front wheel bearing. In the process we will also cover replacing your brakes and repairing your differential seal if it is leaking as 99% of the work will already be done.