Can I rebuild my own steering box?

No need to replace an otherwise re-useable Input Shaft just because the threads are damaged. Rebuilding a Ford Non-Integral steering box is seldom an easy thing to do. Before you consider or attempt a rebuild, there are some problem areas you should be aware of.

How much does it cost to rebuild a steering box?

You will pay anywhere from $600 to $800 for a steering gear box replacement. Labor should run you between $150 and $190, while parts should cost somewhere between $470 and $630.

How do I know if my steering gear box is bad?

How do you know if your steering gearbox is bad?

1. Wandering. A worn steering gear will cause the automobile to wander or veer to one side when operated.
2. Excessive Play. Excessive play in the steering wheel is another symptom that the steering gear is bad or worn.
3. Noise When Turning.
4. Oil Foaming or Discolored.

Is it hard to replace a steering box?

As with most car parts, there will come a time that the gear box will need to be repaired or completely replaced. Installing or adjusting a car’s power steering box can be a relatively easy or somewhat difficult task, depending on the amount of space there is in the engine compartment.

What happens if steering box goes bad?

Steering looseness: Worn internal steering gear components can cause the vehicle’s steering to feel loose. Car is drifting or pulling: A worn or damaged steering gear can result in a vehicle that drifts or pulls to one side.

How long does a steering gear box last?

How often do steering gearboxes need to be replaced? For most vehicles, the power steering system will last well over 100,000 miles before any failures occur.

What happens when steering box goes bad?

Does a new steering box need to be adjusted?

Do not adjust your steering box lash, especially with a new box that has been pre-adjusted. Why, if it is out of adjustment, it needs to be adjusted. The fact that someone else adjusted it wrong is no factor.

Can you over tighten a steering gear box?

If the gear box is tightened too much, the steering wheel will not return when turned and will have to be forced back to straight ahead. If the steering wheel is turned all the way both ways several times, it will loosen up; when it no longer loosens up, it is too tight. Loosen it slightly until it will return easily.

When should I replace my steering gear?

Call when you see the drop arm move, and ask your helper to measure how much the steering wheel has moved. If the steering wheel has moved more than the allowed distance, the box needs adjusting or replacing by a garage.

How can you tell if a steering gearbox is on center?

However its not difficult to tell if a gearbox is on center. The majority of steering gearbox brands, power & manual, have gaps in the pitman shaft splines that tell you if it’s at center; the input shaft provides a clue too. Most pitman shafts are indexed with 4 large spline gaps.

What is the casting number on a GM power steering box?

This gearbox is found in GM trucks and SUV’s from 1987 on. It uses a 3 bolt “triangle” pattern. This box has many variations! There is a casting number on the housing of the gearbox (either 83 or 84). Casting number 83 is a “small bore” GMT400. Casting number 84 is a “big bore” GMT800.

What kind of steering box does Lee power steering use?

This is a guide to help you identify your Saginaw steering box and variations of each steering gearbox. There are 5 different Saginaw steering boxes that Lee Power Steering sells and services. Saginaw 800/808 Gearbox: 1960s-2000s GM Cars and small trucks Saginaw 708 Gearbox: 1960s-1986 GM Trucks/SUV’s

What’s the difference between Saginaw 800 and 808 steering gearbox?

SAGINAW 800/808 GEARBOXES This is the most common GM steering gearbox found in cars and small trucks from the 1960’s into the 2000’s. The difference between the Saginaw 800 and the Saginaw 808 is the size of the piston. The 800 has a 70mm piston and the 808 has an 80mm piston. This is easy to measure from the outside of the gearbox.

How to repair power steering gear box input shaft seal?

Please try again later. Simply needs a couple of small screws and a drill without needs of special tool. I have found this easier way of replacing the input shaft seal of a steering gear box. You don’t have to remove the steering gear box if there is enough access room to work on. Hope this help you good! Loading…

Which is the best power steering gear rebuild kit?

Perfect for the professional or the DIY-er, the Edelmann 8522 Kit can help you fix your leaking power steering gear. With the necessary OE components to rebuild your power steering gear back to its original performance, this kit is an efficient and cost-effective alternative to an expensive power steering gear replacement.

When to replace the steering gear on a Chevy Silverado?

When the gear starts to go bad, you may notice your truck veering to one side, excessive play in the steering, or you might hear a popping or grinding noise while turning. To replace the steering gear, you must first gain access your truck’s steering box. And before you can replace the steering box, you must remove the radiator fan.

What kind of gear is in a steering box?

The conventional steering box accomplishes this with a worm gear, ball nut, and sector gear and shaft housed in the steering box, and steering linkage consisting of a pitman arm, idler arm, center link, and tie-rods, which are attached to the steering knuckles/spindles where the wheels are mounted.