How to remove a Chevy Silverado brake caliper?

Clean out the dirt from inside the torx head bolt. Tap the T55 torx bit with a hammer to seat it into the torx bolt to minimize the risk of stripping. Remove the top caliper torx bolt using a T55 torx bit. Remove the bottom caliper torx bolt using a T55 torx bit. Remove the brake line using an 11mm socket.

What happens when you have a bad brake caliper?

A stuck brake caliper can cause the pads to be pressed against the rotor while driving. As a result, the car may exhibit a dragging sensation, since the brakes at the affected wheel are applied (or partially applied) at all times.

Why do I have spongy brake pedals on my Chevy Silverado?

If your truck has an antilock brake module in it, and that ABS module has air bubbles in it, you will have spongy squishy brake pedal feel even if your ABS system isn’t working. In my case, the brakes were so bad that the brake warning light came on.

How to remove a brake line from a Chevy?

1 Use a small screw driver to clean out the dirt inside the head of the Torx Bolt. 2 Remove the top caliper torx bolt using the T55 torx bit. 3 Remove the bottom caliper torx bolt using the T55 torx bit. 4 Remove the brake line using the 11mm socket.

Where does the brake caliper go on a Chevy Silverado?

The brake caliper for Chevy Silverado 1500 attaches to your suspension and applies pressure to the rotors through the brake pads. By replacing your calipers, the truck’s braking effectiveness is renewed and the effort to brake is minimized.

Why are the brakes soft on my Chevy Silverado?

Air trapped in the lines, calipers or wheel cylinders will make the pedal feel soft and spongy. Air is compressible, so when the brakes are applied any air bubbles in the system must first be compressed before the hydraulic fluid will transmit pressure to apply the brakes.

What happens when your brake calipers get stuck?

Most folks say it smells like rotten eggs Loss of Fuel Mileage – If your Silverado’s brake calipers are stuck even a little bit, fuel mileage will suffer as the engine has to make up for the constant drag coming from the brakes.

How do you Bleed the brakes on a Chevy Silverado?

Close the screw, then bleed both front brakes starting with the right one first. After checking for a firm pedal, drive the vehicle above three miles per hour. The controller will automatically reset the system by commanding the rear motor to run to the home position.

How big is the caliper bolt on a Silverado?

all nbs truck have either a torx 55 or 18mm heads. if you dont want to buy a T55 you can take the 18mm bracket bolts off then the caliper should slide off of the bracket once the rotor isnt in the way. Thanks for everyone’s advice. I’m going to try and re-tackle this brake job tonight or this weekend. Whenever I have a free moment.

Do you replace Torx bolts with standard bolts?

BTW- The Chevy dealers replace the Torx bolts with the standard one’s also. Thanks for posting that. I was looking at the brakes on the truck and saw the torx head. Was wondering about just replacing them with a standard head. Torx are a pain. I have to pull 3 of them to replace wheel bearings in my car.

How much torque does a front brake caliper have?

Application Torque (Nm) Torque (FtLb) Notes Brake caliper bleed nipple 5 3.685 Front brake caliper mounting bolts 28 20.636 Front brake caliper pad retaining pin 18 13.266 I’ve attached the spec chart. Hope this is what you needed.

How much torque does a Silverado rear brake bracket have?

SOURCE: 2004 silverado rear brake torque specification, 31 ft lbs for caliper to bracket, then caliper bracket to nuckle is.148 ft lbs for 6400 & 7200 lbs GVWR or 122 ft lbs for 9900 lbs GVWR or 221 ft lbs for 12300 lbs GVWR. good luck … Brand New Calipers There are brand new additions to the line, as well as updated classics …

Why are the bolts on my caliper not coming out?

The bolts that hold the caliper mounting bracket on just will not come loose. Even air tools will not break them free. Any thoughts on how I can get these things out?

What’s the worst mistake you can make with a caliper?

It is a rookie mistake to go nuts on these bolts and break the heads off. Typically these bolts require only 25- to 35-ft/lbs of torque. Be gentle! 8. Installing a caliper upside down: Nothing is worse than going to bleed a new set of calipers on a vehicle, only to find the bleeders are on the bottom of the caliper and not the top.

What causes a brake caliper to stick while driving?

Besides, the wear and tear lead to accumulation of debris which will cause the calipers to stick. You can replace your bolts and this should solve the problem. In extreme cases, you may be forced to replace the entire brake calipers. Over tightening the bolts can also cause them to break while driving.

What does it mean when your brake caliper is stuck?

“Brake caliper bolt stuck” and “caliper mounting bolt stuck” aren’t phrases I’ve heard anyone say, but thanks to Google they’re likely why you’re reading this. People googled those phrases, and similar ones, over 10,000 times last year. Which means having a stuck caliper bolt is something bugging lots of people.

Why are brake caliper bolts called bracket bolts?

Plain and simple. They’re often called “caliper bracket bolts” because they attach to the part of your caliper called the bracket, and hold it tight to the spindle or steering knuckle. Torque Talk… Now a word about torque, the twisting force that tightens a bolt. Because caliper bolts MUST stay on, they need a LOT of torque.

How much torque does a caliper bracket need?

Torque ranges can vary from 30- to 110-ft/lbs. Also, some bracket bolts can be torque-to-yield or require liquid tread lockers. 7. Over torquing the caliper guide pin bolts: Caliper guide pin bolts typically need a 13mm wrench to remove.

What happens when one brake is stuck on a Chevy Silverado?

Pulling to one side – When one brake is stuck (particularly a front brake) the whole vehicle will pull in the direction of the bad brake. So if it is on the passenger side, your Silverado will feel like it is steering in that direction.

How to remove rear rotors on Silverado 3500HD?

We tried to find a service manual for the truck (2008 Chevrolet Silverado 3500HD 6.6L duramax diesel dually) with no luck. ANY help on removing the rotors to be replaced OR finding a service manual for the truck would help so much!

Do you have to remove rear axle on Silverado?

You might be able to back off the shoes if there is a adjustment hole with a plug in the backing plate. There is NO need to remove the axle unless the seal is leaking.

How can I tell if my Chevy Silverado brakes are due for change?

Installed brake pads, calipers and rotors on Chevy Silverado. You can verify whether your brakes are due for a change by first checking the brake pad thickness. Start by removing the wheel and looking at the brake pads from the top. There should be a piece of metal that extends from the pad and points towards the rotor.

How to freshen up the brakes on a Chevy Silverado?

Here’s how to freshen up the brakes on your Chevy Silverado to keep it stopping at its peak performance. This article applies to the Chevrolet Silverado GMT800 (1999-2006).

Where are the brake caliper mounts on a Chevy Silverado?

(Related Article: How to Jack Up Your Truck – ChevroletForum.com) Remove the two 19mm brake caliper mounting bolts holding the brake caliper to the bracket. These bolts can be found behind the bracket through the little rubber boots. Pull the caliper away from the rotor. Use a bungee cord to hang the caliper, so the brake lines do not get torn.

How do you remove a 19mm brake caliper?

Remove the two 19mm brake caliper mounting bolts holding the brake caliper to the bracket. These bolts can be found behind the bracket through the little rubber boots. Pull the caliper away from the rotor. Use a bungee cord to hang the caliper, so the brake lines do not get torn.

How do you change the brake pads on a Chevy Silverado?

After all of the brake pads, caliper, and rotors have been replaced, you will need to bleed the braking system. Additionally, before driving the truck, pump the brake pedal a few times. Since you retracted the piston, it is not in direct contact with the brake pads, so pumping the brakes will ensure that the piston extends to the pads.

When does a brake rotor need to be replaced?

The brakes can fail if your hydraulic system or master cylinder is leaking. Pulsation: This is the symptom of a brake rotor that has warped. It will need replacement or resurfacing. A rotor face must be within .0005 inch of being parallel and flat with no more than .003 inch of runout.

Where are the brake caliper guide pins located?

To fix this, you have to remove the brake pads and clean the brake pad bracket with a file or sandpaper and lubricate it with copper paste or something similar. The brake caliper guide pins are located at the brake caliper bracket and help the caliper to slide forward and backward when you are braking.

Can a brake caliper stick on a Chevy Silverado?

Your Chevy Silverado’s braking system is the most important safety feature on the vehicle. If it does not work properly, it can put you in a situation where you can be injured or killed. There are quite a few different situations that can cause a caliper to stick.

What happens when you have a problem with your brake calipers?

Whenever you have issues with the brake calipers, you will have problems stopping the car. This can be dangerous, especially when you are traveling at high speeds. The brake calipers have pads attached to them that clap on the wheel rotors.